The effect of low molecular weight surfactants and proteins on surface stickiness of sucrose during powder formation through spray drying
- Adhikari, Benu, Howes, Tony, Wood, B. J., Bhandari, Bhesh
- Authors: Adhikari, Benu , Howes, Tony , Wood, B. J. , Bhandari, Bhesh
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 94, no. 2 (2009), p. 135 -143
- Full Text:
- Reviewed:
- Description: The effect of competitive surface migration of proteins and low molecular weight surfactants (LMS) on the powder recovery in spray drying of highly sticky sugar-rich food has been studied. Sucrose was chosen as a model sugar-rich food because it cannot be easily converted into a pure amorphous powder through spray drying. Sodium caseinate (Na-C) and hydrolyzed whey protein isolate (WPI) were used as model proteins. Polysorbate 80 (Tween-80) and sodium dodecyl sulfate (Na-DS) were used as model non-ionic and ionic LMS. A sucrose solution was spray dried without any additives to establish a base case. Following this, spray drying trials of sucrose-protein solutions were conducted. The sucrose: protein ratio was maintained at 99.5:0.5 and 99.0:1.0. Finally, 0.05% of Tween-80 and Na-DS, on a nominal feed basis, were individually added to the solutions and spray dried. The solid concentration of all of the feed solutions was set at 25% and the inlet and outlet temperatures were maintained at 170 °C and 70 °C, respectively. Powder recovery was determined using a standard procedure and taken as an indicator of the surface stickiness. Coverage of the particle surface by the proteins was determined through elemental surface analysis and a nitrogen balance. It was found that in the absence of LMS, the proteins covered up to 55% of the particle surface and increased the powder recovery to between 84% and 85%. Formation of a glassy protein-rich film acts to reduce the surface stickiness of sucrose droplets. However, when LMS was added to the sucrose-protein solutions, the recovery dropped to zero in the case of Tween-80. In the case of Na-DS the recoveries ranged to 39% and 68%. At these recoveries 83% and 59% of the protein, respectively, was displaced from the surface. This drastic effect of surfactant types on the powder recovery is explained using the Orogenic Displacement model. © 2009 Elsevier Ltd. All rights reserved.
- Authors: Adhikari, Benu , Howes, Tony , Wood, B. J. , Bhandari, Bhesh
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 94, no. 2 (2009), p. 135 -143
- Full Text:
- Reviewed:
- Description: The effect of competitive surface migration of proteins and low molecular weight surfactants (LMS) on the powder recovery in spray drying of highly sticky sugar-rich food has been studied. Sucrose was chosen as a model sugar-rich food because it cannot be easily converted into a pure amorphous powder through spray drying. Sodium caseinate (Na-C) and hydrolyzed whey protein isolate (WPI) were used as model proteins. Polysorbate 80 (Tween-80) and sodium dodecyl sulfate (Na-DS) were used as model non-ionic and ionic LMS. A sucrose solution was spray dried without any additives to establish a base case. Following this, spray drying trials of sucrose-protein solutions were conducted. The sucrose: protein ratio was maintained at 99.5:0.5 and 99.0:1.0. Finally, 0.05% of Tween-80 and Na-DS, on a nominal feed basis, were individually added to the solutions and spray dried. The solid concentration of all of the feed solutions was set at 25% and the inlet and outlet temperatures were maintained at 170 °C and 70 °C, respectively. Powder recovery was determined using a standard procedure and taken as an indicator of the surface stickiness. Coverage of the particle surface by the proteins was determined through elemental surface analysis and a nitrogen balance. It was found that in the absence of LMS, the proteins covered up to 55% of the particle surface and increased the powder recovery to between 84% and 85%. Formation of a glassy protein-rich film acts to reduce the surface stickiness of sucrose droplets. However, when LMS was added to the sucrose-protein solutions, the recovery dropped to zero in the case of Tween-80. In the case of Na-DS the recoveries ranged to 39% and 68%. At these recoveries 83% and 59% of the protein, respectively, was displaced from the surface. This drastic effect of surfactant types on the powder recovery is explained using the Orogenic Displacement model. © 2009 Elsevier Ltd. All rights reserved.
Surface modification of spray dried food and emulsion powders with surface-active proteins : A review
- Jayasundera, Mithila, Adhikari, Benu, Aldred, Peter, Ghandi, Amir
- Authors: Jayasundera, Mithila , Adhikari, Benu , Aldred, Peter , Ghandi, Amir
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 93, no. 3 (2009), p. 266-277
- Full Text:
- Reviewed:
- Description: Spray drying is a well-established and widely used method for transforming a wide range of liquid food products into powder form. Stickiness is the limitation in spray drying of different sugar and acid-rich food products. To minimize this problem process and material science based approaches are in place. However, these remedies have their own drawbacks. Surface modification of droplets/particles is a novel way to minimize stickiness. It is timely that the research efforts on surface modification of droplets/particles be reviewed. Therefore, this review highlights the recent research dealing with surface modification of emulsions and spray dried powders. The theoretical foundation, mechanisms and methods used to achieve surface modification of food and emulsion powders are highlighted. © 2009 Elsevier Ltd. All rights reserved.
- Authors: Jayasundera, Mithila , Adhikari, Benu , Aldred, Peter , Ghandi, Amir
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 93, no. 3 (2009), p. 266-277
- Full Text:
- Reviewed:
- Description: Spray drying is a well-established and widely used method for transforming a wide range of liquid food products into powder form. Stickiness is the limitation in spray drying of different sugar and acid-rich food products. To minimize this problem process and material science based approaches are in place. However, these remedies have their own drawbacks. Surface modification of droplets/particles is a novel way to minimize stickiness. It is timely that the research efforts on surface modification of droplets/particles be reviewed. Therefore, this review highlights the recent research dealing with surface modification of emulsions and spray dried powders. The theoretical foundation, mechanisms and methods used to achieve surface modification of food and emulsion powders are highlighted. © 2009 Elsevier Ltd. All rights reserved.
Effect of addition of proteins on the production of amorphous sucrose powder through spray drying
- Adhikari, Benu, Howes, Tony, Bhandari, Bhesh, Langrish, Tim
- Authors: Adhikari, Benu , Howes, Tony , Bhandari, Bhesh , Langrish, Tim
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 94, no. 2 (2009), p. 144 -153
- Full Text:
- Reviewed:
- Description: Spray drying trials were carried out to produce amorphous sucrose powder. Firstly, pure sucrose solutions were prepared and spray dried at inlet and outlet temperatures of 160 °C and 70 °C, respectively. No amorphous powder was obtained and only 18% of the feed solids were recovered in a crystalline form, with the remaining solids lost as wall deposits. Secondly, sodium caseinate (Na-C) and hydrolyzed whey protein isolate (WPI) were added in sucrose:protein solid ratios of (99.5:0.5) and (99.0:1.0) and drying trials were conducted maintaining the initial drying conditions. In both these cases, greater than 80% of the feed solids were recovered in an amorphous form. The increase in protein concentration from 0.5% to 1% on dry solid basis did not further improve the recovery. The remarkable increase in recovery from a small addition of protein is attributed to preferential migration of protein molecules to the droplet-air interface, and the subsequent transformation of the thin, protein-rich film into a non-sticky glassy state upon drying. This film overcomes both the particle-to-particle and particle-to-wall stickiness. The measured bulk glass rubber transition temperature (Tg-r) values of the bulk mixtures at various moisture contents were very close to the corresponding mean glass transition temperature (Tg) of the pure sucrose indicating that surface layer Tg rather than the bulk Tg is responsible for this. Electron spectroscopy for chemical analysis (ESCA) studies revealed that the particle surface was covered by 50-58% (by mass) proteins. The calculated glass transition temperature of the surface layer (Tg,surface layer), based on the surface elemental compositions, showed that the Tg,surface layer has increased to the extent that it remained within the safe drying envelope of spray drying. © 2009 Elsevier Ltd. All rights reserved.
- Authors: Adhikari, Benu , Howes, Tony , Bhandari, Bhesh , Langrish, Tim
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 94, no. 2 (2009), p. 144 -153
- Full Text:
- Reviewed:
- Description: Spray drying trials were carried out to produce amorphous sucrose powder. Firstly, pure sucrose solutions were prepared and spray dried at inlet and outlet temperatures of 160 °C and 70 °C, respectively. No amorphous powder was obtained and only 18% of the feed solids were recovered in a crystalline form, with the remaining solids lost as wall deposits. Secondly, sodium caseinate (Na-C) and hydrolyzed whey protein isolate (WPI) were added in sucrose:protein solid ratios of (99.5:0.5) and (99.0:1.0) and drying trials were conducted maintaining the initial drying conditions. In both these cases, greater than 80% of the feed solids were recovered in an amorphous form. The increase in protein concentration from 0.5% to 1% on dry solid basis did not further improve the recovery. The remarkable increase in recovery from a small addition of protein is attributed to preferential migration of protein molecules to the droplet-air interface, and the subsequent transformation of the thin, protein-rich film into a non-sticky glassy state upon drying. This film overcomes both the particle-to-particle and particle-to-wall stickiness. The measured bulk glass rubber transition temperature (Tg-r) values of the bulk mixtures at various moisture contents were very close to the corresponding mean glass transition temperature (Tg) of the pure sucrose indicating that surface layer Tg rather than the bulk Tg is responsible for this. Electron spectroscopy for chemical analysis (ESCA) studies revealed that the particle surface was covered by 50-58% (by mass) proteins. The calculated glass transition temperature of the surface layer (Tg,surface layer), based on the surface elemental compositions, showed that the Tg,surface layer has increased to the extent that it remained within the safe drying envelope of spray drying. © 2009 Elsevier Ltd. All rights reserved.
Effect of proteins and low molecular weight surfactants on spray-drying and powder properties of sugar-rich foods
- Authors: Jayasundera, Mithila
- Date: 2011
- Type: Text , Thesis , PhD
- Full Text:
- Description: The effect of proteins and low molecular weight surfactants on spray-drying and powder properties of sugar-rich foods has been studied. This PhD study was aimed at quantifying both the extent and effects of the migration of protein and surfactant to the powder surface of spray-dried sugar-rich foods and their implications for powder formation yields and the powder properties such as moisture content, water activity, particle size, glass transition temperature, amorphous/crystalline nature, surface protein coverage, surface stickiness and reconstitution (solubility). The use of proteins and to a lesser extent surfactants as drying aids for sugar rich foods is novel. Sodium caseinate can act as a ‘smart’ drying aid in producing powders out of sugar-rich foods due to their higher solubility and better film-forming property. The remarkable behaviour of sodium caseinate as a drying aid, especially for sucrose is a very significant result both scientifically and commercially. The surface protein coverage and the recovery of the powder in sucrose–protein systems were found to be very sensitive in the presence of low molecular weight surfactants as the concentration of the sodium caseinate in the bulk was below its critical micelle concentration. However, the type of low molecular weight surfactants had no effect on the amorphous nature of fructose–protein powders mainly due to higher protein content (higher than critical micelle concentration) in these powders. It has been found that the nature of the sugar (sucrose or fructose), especially its glass transition temperature determines the extent of protein required to achieve a comparable powder recovery. The maximum solubility of the protein content of sugar–protein and sugar–protein–surfactant powders was achieved within 5 minutes of dissolution.
- Description: Doctor of Philosophy
- Authors: Jayasundera, Mithila
- Date: 2011
- Type: Text , Thesis , PhD
- Full Text:
- Description: The effect of proteins and low molecular weight surfactants on spray-drying and powder properties of sugar-rich foods has been studied. This PhD study was aimed at quantifying both the extent and effects of the migration of protein and surfactant to the powder surface of spray-dried sugar-rich foods and their implications for powder formation yields and the powder properties such as moisture content, water activity, particle size, glass transition temperature, amorphous/crystalline nature, surface protein coverage, surface stickiness and reconstitution (solubility). The use of proteins and to a lesser extent surfactants as drying aids for sugar rich foods is novel. Sodium caseinate can act as a ‘smart’ drying aid in producing powders out of sugar-rich foods due to their higher solubility and better film-forming property. The remarkable behaviour of sodium caseinate as a drying aid, especially for sucrose is a very significant result both scientifically and commercially. The surface protein coverage and the recovery of the powder in sucrose–protein systems were found to be very sensitive in the presence of low molecular weight surfactants as the concentration of the sodium caseinate in the bulk was below its critical micelle concentration. However, the type of low molecular weight surfactants had no effect on the amorphous nature of fructose–protein powders mainly due to higher protein content (higher than critical micelle concentration) in these powders. It has been found that the nature of the sugar (sucrose or fructose), especially its glass transition temperature determines the extent of protein required to achieve a comparable powder recovery. The maximum solubility of the protein content of sugar–protein and sugar–protein–surfactant powders was achieved within 5 minutes of dissolution.
- Description: Doctor of Philosophy
- «
- ‹
- 1
- ›
- »