Vehicle driving cycle performance of the spark-less di-ji hydrogen engine
- Authors: Boretti, Alberto
- Date: 2010
- Type: Text , Journal article
- Relation: International Journal of Hydrogen Energy Vol. 35, no. 10 (2010), p. 4702-4714
- Full Text:
- Reviewed:
- Description: The paper describes coupled CFD combustion simulations and CAE engine performance computations to describe the operation over the full range of load and speed of an always lean burn, Direct Injection Jet Ignition (DI-JI) hydrogen engine. Jet ignition pre-chambers and direct injection are enablers of high efficiencies and load control by quantity of fuel injected. Towards the end of the compression stroke, a small quantity of hydrogen is injected within the spark-less pre-chamber of the DI-JI engine, where it mixes with the air entering from the main chamber and auto-ignites because of the high temperature of the hot glow plug. Then, jets of partially combusted hot gases enter the main chamber igniting there in the bulk, over multiple ignition points, lean stratified mixtures of air and fuel. Engine maps of brake specific fuel consumption vs. speed and brake mean effective pressure are computed first. CAE vehicle simulations are finally performed evaluating the fuel consumption over emission cycles of a vehicle equipped with this engine. © 2010 Professor T. Nejat Veziroglu.
- Description: The paper describes coupled CFD combustion simulations and CAE engine performance computations to describe the operation over the full range of load and speed of an always lean burn, Direct Injection Jet Ignition (DI-JI) hydrogen engine. Jet ignition pre-chambers and direct injection are enablers of high efficiencies and load control by quantity of fuel injected. Towards the end of the compression stroke, a small quantity of hydrogen is injected within the spark-less pre-chamber of the DI-JI engine, where it mixes with the air entering from the main chamber and auto-ignites because of the high temperature of the hot glow plug. Then, jets of partially combusted hot gases enter the main chamber igniting there in the bulk, over multiple ignition points, lean stratified mixtures of air and fuel. Engine maps of brake specific fuel consumption vs. speed and brake mean effective pressure are computed first. CAE vehicle simulations are finally performed evaluating the fuel consumption over emission cycles of a vehicle equipped with this engine. © 2010 Professor T. Nejat Veziroglu.
- Authors: Boretti, Alberto
- Date: 2010
- Type: Text , Journal article
- Relation: International Journal of Hydrogen Energy Vol. 35, no. 10 (2010), p. 4702-4714
- Full Text:
- Reviewed:
- Description: The paper describes coupled CFD combustion simulations and CAE engine performance computations to describe the operation over the full range of load and speed of an always lean burn, Direct Injection Jet Ignition (DI-JI) hydrogen engine. Jet ignition pre-chambers and direct injection are enablers of high efficiencies and load control by quantity of fuel injected. Towards the end of the compression stroke, a small quantity of hydrogen is injected within the spark-less pre-chamber of the DI-JI engine, where it mixes with the air entering from the main chamber and auto-ignites because of the high temperature of the hot glow plug. Then, jets of partially combusted hot gases enter the main chamber igniting there in the bulk, over multiple ignition points, lean stratified mixtures of air and fuel. Engine maps of brake specific fuel consumption vs. speed and brake mean effective pressure are computed first. CAE vehicle simulations are finally performed evaluating the fuel consumption over emission cycles of a vehicle equipped with this engine. © 2010 Professor T. Nejat Veziroglu.
- Description: The paper describes coupled CFD combustion simulations and CAE engine performance computations to describe the operation over the full range of load and speed of an always lean burn, Direct Injection Jet Ignition (DI-JI) hydrogen engine. Jet ignition pre-chambers and direct injection are enablers of high efficiencies and load control by quantity of fuel injected. Towards the end of the compression stroke, a small quantity of hydrogen is injected within the spark-less pre-chamber of the DI-JI engine, where it mixes with the air entering from the main chamber and auto-ignites because of the high temperature of the hot glow plug. Then, jets of partially combusted hot gases enter the main chamber igniting there in the bulk, over multiple ignition points, lean stratified mixtures of air and fuel. Engine maps of brake specific fuel consumption vs. speed and brake mean effective pressure are computed first. CAE vehicle simulations are finally performed evaluating the fuel consumption over emission cycles of a vehicle equipped with this engine. © 2010 Professor T. Nejat Veziroglu.
Modelling auto ignition of hydrogen in a jet ignition pre-chamber
- Authors: Boretti, Alberto
- Date: 2010
- Type: Text , Journal article
- Relation: International Journal of Hydrogen Energy Vol. 35, no. 8 (2010), p. 3881-3890
- Full Text:
- Reviewed:
- Description: Spark-less jet ignition pre-chambers are enablers of high efficiencies and load control by quantity of fuel injected when coupled with direct injection of main chamber fuel, thus permitting always lean burn bulk stratified combustion. Towards the end of the compression stroke, a small quantity of hydrogen is injected within the pre-chamber, where it mixes with the air entering from the main chamber. Combustion of the air and fuel mixture then starts within the pre-chamber because of the high temperature of the hot glow plug, and then jets of partially combusted hot gases enter the main chamber igniting there in the bulk, over multiple ignition points, lean stratified mixtures of air and fuel. The paper describes the operation of the spark-less jet ignition pre-chamber coupling CFD and CAE engine simulations to allow component selection and engine performance evaluation. © 2010 Professor T. Nejat Veziroglu.
- Authors: Boretti, Alberto
- Date: 2010
- Type: Text , Journal article
- Relation: International Journal of Hydrogen Energy Vol. 35, no. 8 (2010), p. 3881-3890
- Full Text:
- Reviewed:
- Description: Spark-less jet ignition pre-chambers are enablers of high efficiencies and load control by quantity of fuel injected when coupled with direct injection of main chamber fuel, thus permitting always lean burn bulk stratified combustion. Towards the end of the compression stroke, a small quantity of hydrogen is injected within the pre-chamber, where it mixes with the air entering from the main chamber. Combustion of the air and fuel mixture then starts within the pre-chamber because of the high temperature of the hot glow plug, and then jets of partially combusted hot gases enter the main chamber igniting there in the bulk, over multiple ignition points, lean stratified mixtures of air and fuel. The paper describes the operation of the spark-less jet ignition pre-chamber coupling CFD and CAE engine simulations to allow component selection and engine performance evaluation. © 2010 Professor T. Nejat Veziroglu.
Identification of fromiamycalin and halaminol A from Australian marine sponge extracts with anthelmintic activity against haemonchus contortus
- Herath, Dilrukshi, Preston, Sarah, Jabbar, Abdul, Garcia-Bustos, Jose, Taki, Aya, Addison, Russell, Hayes, Sasha, Beattie, Karren, McGee, Sean, Martin, Sheree, Ekin, Merrick, Hooper, John, Chang, Bill, Hofmann, Andreas, Davis, Rohan, Gasser, Robin
- Authors: Herath, Dilrukshi , Preston, Sarah , Jabbar, Abdul , Garcia-Bustos, Jose , Taki, Aya , Addison, Russell , Hayes, Sasha , Beattie, Karren , McGee, Sean , Martin, Sheree , Ekin, Merrick , Hooper, John , Chang, Bill , Hofmann, Andreas , Davis, Rohan , Gasser, Robin
- Date: 2019
- Type: Text , Journal article
- Relation: Marine Drugs Vol. 17, no. 11 (Nov 2019), p. 14
- Full Text:
- Reviewed:
- Description: There is an urgent need to discover and develop new anthelmintics for the treatment of parasitic nematodes of veterinary importance to circumvent challenges linked to drug resistant parasites. Being one of the most diverse natural ecosystems, the marine environment represents a rich resource of novel chemical entities. This study investigated 2000 extracts from marine invertebrates, collected from Australian waters, for anthelmintic activity. Using a well-established in vitro bioassay, these extracts were screened for nematocidal activity against Haemonchus contortus - a socioeconomically important parasitic nematode of livestock animals. Extracts (designated Mu-1, Ha-1 and Ha-2) from two marine sponges (Monanchora unguiculata and Haliclona sp.) each significantly affected larvae of H. contortus. Individual extracts displayed a dose-dependent inhibition of both the motility of exsheathed third-stage larvae (xL3s) and the development of xL3s to fourth-stage larvae (L4s). Active fractions in each of the three extracts were identified using bioassay-guided fractionation. From the active fractions from Monanchora unguiculata, a known pentacyclic guanidine alkaloid, fromiamycalin (1), was purified. This alkaloid was shown to be a moderately potent inhibitor of L4 development (half-maximum inhibitory concentration (IC50) = 26.6 +/- 0.74 mu M) and L4 motility (IC50 = 39.4 +/- 4.83 mu M), although it had a relatively low potency at inhibiting of xL3 motility (IC50 >= 100 mu M). Investigation of the active fractions from the two Haliclona collections led to identification of a mixture of amino alcohol lipids, and, subsequently, a known natural product halaminol A (5). Anthelmintic profiling showed that 5 had limited potency at inhibiting larval development and motility. These data indicate that fromiamycalin, other related pentacyclic guanidine alkaloids and/or halaminols could have potential as anthelmintics following future medicinal chemistry efforts.
- Authors: Herath, Dilrukshi , Preston, Sarah , Jabbar, Abdul , Garcia-Bustos, Jose , Taki, Aya , Addison, Russell , Hayes, Sasha , Beattie, Karren , McGee, Sean , Martin, Sheree , Ekin, Merrick , Hooper, John , Chang, Bill , Hofmann, Andreas , Davis, Rohan , Gasser, Robin
- Date: 2019
- Type: Text , Journal article
- Relation: Marine Drugs Vol. 17, no. 11 (Nov 2019), p. 14
- Full Text:
- Reviewed:
- Description: There is an urgent need to discover and develop new anthelmintics for the treatment of parasitic nematodes of veterinary importance to circumvent challenges linked to drug resistant parasites. Being one of the most diverse natural ecosystems, the marine environment represents a rich resource of novel chemical entities. This study investigated 2000 extracts from marine invertebrates, collected from Australian waters, for anthelmintic activity. Using a well-established in vitro bioassay, these extracts were screened for nematocidal activity against Haemonchus contortus - a socioeconomically important parasitic nematode of livestock animals. Extracts (designated Mu-1, Ha-1 and Ha-2) from two marine sponges (Monanchora unguiculata and Haliclona sp.) each significantly affected larvae of H. contortus. Individual extracts displayed a dose-dependent inhibition of both the motility of exsheathed third-stage larvae (xL3s) and the development of xL3s to fourth-stage larvae (L4s). Active fractions in each of the three extracts were identified using bioassay-guided fractionation. From the active fractions from Monanchora unguiculata, a known pentacyclic guanidine alkaloid, fromiamycalin (1), was purified. This alkaloid was shown to be a moderately potent inhibitor of L4 development (half-maximum inhibitory concentration (IC50) = 26.6 +/- 0.74 mu M) and L4 motility (IC50 = 39.4 +/- 4.83 mu M), although it had a relatively low potency at inhibiting of xL3 motility (IC50 >= 100 mu M). Investigation of the active fractions from the two Haliclona collections led to identification of a mixture of amino alcohol lipids, and, subsequently, a known natural product halaminol A (5). Anthelmintic profiling showed that 5 had limited potency at inhibiting larval development and motility. These data indicate that fromiamycalin, other related pentacyclic guanidine alkaloids and/or halaminols could have potential as anthelmintics following future medicinal chemistry efforts.
A modified MTS proliferation assay for suspended cells to avoid the interference by hydralazine and β-Mercaptoethanol
- Wang, Yutang, Nguyen, Dinh, Anesi, Jack, Kelly, Jason, Ahmady, Fahima, Charchar, Fadi
- Authors: Wang, Yutang , Nguyen, Dinh , Anesi, Jack , Kelly, Jason , Ahmady, Fahima , Charchar, Fadi
- Date: 2021
- Type: Text , Journal article
- Relation: Assay and Drug Development Technologies Vol. 19, no. 3 (2021), p. 184-190. https://purl.org/au-research/grants/nhmrc/1062671
- Full Text:
- Reviewed:
- Description: The 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium (MTS) assay is one of the most commonly used tests of cell proliferation. Hydralazine has been reported to interfere with the performance of the MTS assay when used on adherent cells. This study aimed to investigate whether hydralazine interferes with the performance of the MTS assay on suspended cells. THP-1 (a monocytic leukemia cell line) cells were cultured in the presence or absence of hydralazine (0, 10, 50, 100, and 500 μM) for 2 or 24 h. Cell numbers were analyzed using the MTS, trypan blue exclusion, or microscopic assays. A modified version of the standard MTS assay was established by centrifuging the cells and replacing the test medium with fresh culture medium immediately before the addition of the MTS reagent. Culture of THP-1 cells with hydralazine at concentrations of 50, 100, and 500 μM for 2 h increased absorbance (p < 0.001) in the standard MTS assay, whereas both the trypan blue exclusion assay and microscopy suggested no change in cell numbers. Culture of THP-1 cells with 100 and 500 μm hydralazine for 24 h increased absorbance (p < 0.05) in the standard MTS assay; however, trypan blue exclusion and microscopy suggested a decrease in cell numbers. In a cell-free system, hydralazine (100 and 500 μM) increased absorbance in a time- and concentration-dependent manner. The modified MTS assay produced results consistent with trypan blue exclusion and microscopy using THP-1 cells. In addition, the modified MTS assay produced reliable results when K562 and Jurkat cells were incubated with hydralazine or β-mercaptoethanol (βME). In conclusion, a simple modification of the standard MTS assay overcame the interference of hydralazine and βME when assessing suspended cells. © Copyright 2021, Mary Ann Liebert, Inc., publishers 2021. *Please note that there are multiple authors for this article therefore only the name of the Federation University Australia affiliates “Yutang Wang, Dinh Nguyen, Jack Anesi, Jason Kelly, Fahima Ahmady, Fadi Charchar" is provided in this record**
- Authors: Wang, Yutang , Nguyen, Dinh , Anesi, Jack , Kelly, Jason , Ahmady, Fahima , Charchar, Fadi
- Date: 2021
- Type: Text , Journal article
- Relation: Assay and Drug Development Technologies Vol. 19, no. 3 (2021), p. 184-190. https://purl.org/au-research/grants/nhmrc/1062671
- Full Text:
- Reviewed:
- Description: The 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium (MTS) assay is one of the most commonly used tests of cell proliferation. Hydralazine has been reported to interfere with the performance of the MTS assay when used on adherent cells. This study aimed to investigate whether hydralazine interferes with the performance of the MTS assay on suspended cells. THP-1 (a monocytic leukemia cell line) cells were cultured in the presence or absence of hydralazine (0, 10, 50, 100, and 500 μM) for 2 or 24 h. Cell numbers were analyzed using the MTS, trypan blue exclusion, or microscopic assays. A modified version of the standard MTS assay was established by centrifuging the cells and replacing the test medium with fresh culture medium immediately before the addition of the MTS reagent. Culture of THP-1 cells with hydralazine at concentrations of 50, 100, and 500 μM for 2 h increased absorbance (p < 0.001) in the standard MTS assay, whereas both the trypan blue exclusion assay and microscopy suggested no change in cell numbers. Culture of THP-1 cells with 100 and 500 μm hydralazine for 24 h increased absorbance (p < 0.05) in the standard MTS assay; however, trypan blue exclusion and microscopy suggested a decrease in cell numbers. In a cell-free system, hydralazine (100 and 500 μM) increased absorbance in a time- and concentration-dependent manner. The modified MTS assay produced results consistent with trypan blue exclusion and microscopy using THP-1 cells. In addition, the modified MTS assay produced reliable results when K562 and Jurkat cells were incubated with hydralazine or β-mercaptoethanol (βME). In conclusion, a simple modification of the standard MTS assay overcame the interference of hydralazine and βME when assessing suspended cells. © Copyright 2021, Mary Ann Liebert, Inc., publishers 2021. *Please note that there are multiple authors for this article therefore only the name of the Federation University Australia affiliates “Yutang Wang, Dinh Nguyen, Jack Anesi, Jason Kelly, Fahima Ahmady, Fadi Charchar" is provided in this record**
An improved 3-(4,5-dmethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl )-2H-tetrazolium proliferation assay to overcome the interference of hydralazine
- Wang, Yutang, Nguyen, Dinh, Yang, Guang, Anesi, Jack, Chai, Zhonglin, Charchar, Fadi, Golledge, Jonathan
- Authors: Wang, Yutang , Nguyen, Dinh , Yang, Guang , Anesi, Jack , Chai, Zhonglin , Charchar, Fadi , Golledge, Jonathan
- Date: 2020
- Type: Text , Journal article
- Relation: Assay and Drug Development Technologies Vol. 18, no. 8 (Dec 2020), p. 379-384
- Relation: https://purl.org/au-research/grants/nhmrc/1062671
- Full Text:
- Reviewed:
- Description: The MTS [3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium] assay is one of the most commonly used assays to assess cell proliferation and cytotoxicity, but is subject to interference by testing compounds. Hydralazine, an antihypertensive drug, is commonly investigated in multiple fields such as heart failure, cancer, and blood pressure research. This study reported interference of the MTS assay by hydralazine and a simple modification overcoming this interference. Vascular smooth muscle cells were cultured in the presence or absence of hydralazine (0, 10, 50,100, and 500 mu M) for 2 or 24 h. Cell numbers were analyzed using MTS, trypan blue exclusion, or microscopic assays. A modified version of the standard MTS assay was established, in which an additional step was added replacing the test medium, containing hydralazine, with fresh culture medium immediately before the addition of the MTS reagent. Culture with hydralazine at concentrations of 50, 100, and 500 mu M for 2 h increased absorbance (p< 0.05) in the standard MTS assay, whereas microscopy suggested no change in cell numbers. Culture with 500 mu m hydralazine for 24 h increased absorbance (p< 0.05) in the standard MTS assay, however, trypan blue exclusion and microscopy suggested a decrease in cell numbers. In a cell-free system, hydralazine (>= 10 mu M) increased absorbance in a concentration-dependent manner. The modified MTS assay produced results consistent with trypan blue exclusion and microscopy. In conclusion, a simple modification of the standard MTS assay overcame the interference of hydralazine and may be useful to avoid interference from other tested compounds.
- Authors: Wang, Yutang , Nguyen, Dinh , Yang, Guang , Anesi, Jack , Chai, Zhonglin , Charchar, Fadi , Golledge, Jonathan
- Date: 2020
- Type: Text , Journal article
- Relation: Assay and Drug Development Technologies Vol. 18, no. 8 (Dec 2020), p. 379-384
- Relation: https://purl.org/au-research/grants/nhmrc/1062671
- Full Text:
- Reviewed:
- Description: The MTS [3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium] assay is one of the most commonly used assays to assess cell proliferation and cytotoxicity, but is subject to interference by testing compounds. Hydralazine, an antihypertensive drug, is commonly investigated in multiple fields such as heart failure, cancer, and blood pressure research. This study reported interference of the MTS assay by hydralazine and a simple modification overcoming this interference. Vascular smooth muscle cells were cultured in the presence or absence of hydralazine (0, 10, 50,100, and 500 mu M) for 2 or 24 h. Cell numbers were analyzed using MTS, trypan blue exclusion, or microscopic assays. A modified version of the standard MTS assay was established, in which an additional step was added replacing the test medium, containing hydralazine, with fresh culture medium immediately before the addition of the MTS reagent. Culture with hydralazine at concentrations of 50, 100, and 500 mu M for 2 h increased absorbance (p< 0.05) in the standard MTS assay, whereas microscopy suggested no change in cell numbers. Culture with 500 mu m hydralazine for 24 h increased absorbance (p< 0.05) in the standard MTS assay, however, trypan blue exclusion and microscopy suggested a decrease in cell numbers. In a cell-free system, hydralazine (>= 10 mu M) increased absorbance in a concentration-dependent manner. The modified MTS assay produced results consistent with trypan blue exclusion and microscopy. In conclusion, a simple modification of the standard MTS assay overcame the interference of hydralazine and may be useful to avoid interference from other tested compounds.
Colloidal carbon interference in the treatability of pulp and paper wastewater by MBR
- Scholes, Emily, Brook-Carter, Phillip, Verheyen, Vincent
- Authors: Scholes, Emily , Brook-Carter, Phillip , Verheyen, Vincent
- Date: 2019
- Type: Text , Journal article
- Relation: Journal of Environmental Chemical Engineering Vol. 7, no. 5 (2019), p. 1-9
- Full Text:
- Reviewed:
- Description: Pulp and paper wastewaters are challenging to treat due to their variability, complexity and toxicity. Membrane Bioreactor’s (MBR’s) provide high-quality filtrates but are subject to periods of low filterability / high capillary suction time (CST) which potentially limit their use in this application. There is a paucity of published literature concerning long-term operational issues in full-scale, industrial MBR’s. We hypothesised that either changes of bacterial population, alteration/reduction of bacterial metabolism or bacterial production of extra-cellular polymers (ESPs) increased CST and reduced filterability. This study, conducted over two years at the 16.4MLD Gippsland Water Factory, was structured to inform this bacterial centric hypothesis. However, no shifts in bacterial population were seen as causative of high CST and microbial stress levels and biological activity were observed to be low during high CST and no sign of toxicity was found. The strongest correlator with CST was the concentration of colloidal Total Organic Carbon of the mixed liquor suspended solids (MLSS) supernatant (following centrifugation). The carbonaceous colloids accumulated in the supernatant were named ‘Non-Centrifugable Total Organic Carbon’ (NCTOC). Their accumulation in the MLSS was found be due to their biologically refractory nature and their retention by the MBR membrane. The accumulation of NCTOC typically followed a period where the influent had a high colour and a high sodium to calcium ratio, which is consistent with a pulping by-product called ‘Black Liquor’. Additional experiments with Black Liquor allowed us to conclude that high CST can be produced by addition of Black Liquor.
- Authors: Scholes, Emily , Brook-Carter, Phillip , Verheyen, Vincent
- Date: 2019
- Type: Text , Journal article
- Relation: Journal of Environmental Chemical Engineering Vol. 7, no. 5 (2019), p. 1-9
- Full Text:
- Reviewed:
- Description: Pulp and paper wastewaters are challenging to treat due to their variability, complexity and toxicity. Membrane Bioreactor’s (MBR’s) provide high-quality filtrates but are subject to periods of low filterability / high capillary suction time (CST) which potentially limit their use in this application. There is a paucity of published literature concerning long-term operational issues in full-scale, industrial MBR’s. We hypothesised that either changes of bacterial population, alteration/reduction of bacterial metabolism or bacterial production of extra-cellular polymers (ESPs) increased CST and reduced filterability. This study, conducted over two years at the 16.4MLD Gippsland Water Factory, was structured to inform this bacterial centric hypothesis. However, no shifts in bacterial population were seen as causative of high CST and microbial stress levels and biological activity were observed to be low during high CST and no sign of toxicity was found. The strongest correlator with CST was the concentration of colloidal Total Organic Carbon of the mixed liquor suspended solids (MLSS) supernatant (following centrifugation). The carbonaceous colloids accumulated in the supernatant were named ‘Non-Centrifugable Total Organic Carbon’ (NCTOC). Their accumulation in the MLSS was found be due to their biologically refractory nature and their retention by the MBR membrane. The accumulation of NCTOC typically followed a period where the influent had a high colour and a high sodium to calcium ratio, which is consistent with a pulping by-product called ‘Black Liquor’. Additional experiments with Black Liquor allowed us to conclude that high CST can be produced by addition of Black Liquor.
- «
- ‹
- 1
- ›
- »