Description:
Stickiness of whey protein isolate (WPI) and spray dried lactose droplets was studied at two air temperatures (65±0.5°C, 80±0.5°C), 0.75 m/s air velocity and 2-2.5% relative humidity using an in situ stickiness testing device. A stainless steel probe with 50 mm/min contact/withdrawal speed was used. The moisture and temperature histories were measured through parallel experiments. In each case, the surface of the lactose droplet remained sticky and failed cohesively until the surface was completely surrounded with crystals. The crystal layer remained fragile, fractured upon the probe contact and a thin layer of solution came out to the probe surface even after the moisture (u, dry basis) was lower than 0.2. WPI droplets formed thin and smooth skin immediately after coming in contact with hot air. The tensile strength of this skin increased rapidly and peaked (u = 2.14 at 45°C and u = 1. 47 at 65.7°C) fairly early during drying process. WPI droplet surface became completely non-sticky soon after attaining the peak tensile strength (u =1.32 at 53.4 °C and u= 1.05 at 68.8°C), mainly due to transformation of the outer layer of the skin into glassy material. The skin forming and surface active nature of WPI was exploited to minimize the stickiness of honey during spray drying. Replacement of 5% (w/w) maltodextrin with WPI raised the powder recovery of honey solids from 28% to 80%. Stickiness of the WPI on glass, Teflon and polyurethane surfaces was studied by replacing the contact surface of the probe with these materials. It was found that the stickiness of glass surface was the highest at test temperatures. Teflon surface offered the lowest stickiness at the test temperatures making it suitable materials to minimize solution/particle stickiness through coating.
Description:
The idea of publishing a special issue on proteins and enzymes was conceived during the 18th International Drying Symposium (IDS2012) held in the historical city of Xiamen, China (November 11-15, 2012). It appeared to us that a number of scientists and engineers were enthusiastically undertaking research in various aspects of drying of proteins and enzymes. Professors Arun Mujumdar and Sakamon Devhastin encouraged me to explore the possibility of bringing at least one special issue that would depict contemporary research undertakings in the broader theme involving proteins and enzymes. We were somewhat unsure in the beginning whether or not the required number of high quality mansucripts could be garnered for one issue in the time constraint we had in mind. Editorial
Description:
A stickiness testing device based on the probe tack test has been designed and tested. It was used to perform in situ characterization of drying hemispherical drops with an initial radius 3.5 mm. Tests were carried out in two drying temperatures, 63 and 95 degreesC. Moisture and temperature histories of the drying drops of fructose, honey, sucrose, maltodextrin and sucrose-maltodextrin mixtures were determined. The rates of moisture evaporation of the fructose solution was the fastest while those of the maltodextrin solution was the lowest. A profile reversal was observed when the temperature profiles of these materials were compared. Different modes of failure were observed during the stickiness tests. Pure fructose and honey solutions remained completely sticky and failed cohesively until the end of drying. Pure sucrose solution remained sticky and failed cohesively until complete crystallization occurred. The surface of the maltodextrin drops formed a skin shortly after the start of drying. It exhibited adhesive failure and reached a state of non-adhesion. Addition of maltodextrin significantly altered the stickiness of sucrose solution. (C) 2002 Elsevier Science Ltd. All rights reserved.
Description:
Drying kinetics of low molecular weight sugars such as fructose, glucose, sucrose and organic acid such as citric acid and high molecular weight carbohydrate such as maltodextrin (DE 6) were determined experimentally using single drop drying experiments as well as predicted numerically by solving the mass and heat transfer equations. The predicted moisture and temperature histories agreed with the experimental ones within 6% average relative (absolute) error and average difference of +/- 1degreesC, respectively. The stickiness histories of these drops were determined experimentally and predicted numerically based on the glass transition temperature (T-g) of surface layer. The model predicted the experimental observations with good accuracy. A nonsticky regime for these materials during spray drying is proposed by simulating a drop, initially 120 mum in diameter, in a spray drying environment.
Description:
Solutions of fructose, maltodextrin (DE 5), and their mixtures at the ratios of 20:80, 40:60, 50:50, 60:40, and 80:20 were gelled with 1% agar-agar and dried under convective-conductive drying conditions. The thin slabs were maintained at isothermal drying condition of 30 and 50 degrees C. Yamamoto's simplified method based on regular regime approach was used to calculate the (effective) moisture diffusivity. Both the drying rates and the moisture diffusivity exhibited strong concentration dependence. The concentration dependence was stronger in the case of fructose and fructose rich solutions. Both the moisture diffusivity and drying rates of the mixture solutions were enhanced due to plasticization of fructose on maltodextrin, which is explained through free volume theory.
Description:
We report the synergistic and competitive interactions between multiple plasticizers in plasticized low-amylose starch that result in either enhanced or reduced water migration fluxes and effective moisture diffusivities. The starch was plasticized using glycerol and xylitol either individually or in 1:1 combination. The water migration fluxes and moisture diffusivities were higher in xylitol plasticized films compared to the glycerol plasticized ones. For low plasticizer concentrations, the presence of both the plasticizers competitively reduced the effective moisture diffusivities and moisture migration fluxes due to antiplasticization. However, at higher plasticizer contents (at and above 15wt%), the presence of multiple plasticizers enhanced the moisture migration fluxes and effective moisture diffusivities due to synergistic plasticization. The moisture migration fluxes and effective moisture diffusivities exhibited both moisture and plasticizer concentration dependence and the former was found to be stronger than the latter. These findings can be used for designing and controlling the vapor barrier properties of starch-based bioplastics during drying and formulation phase.
Description:
A probe tack test has been used for the in situ characterization of the surface stickiness of hemispherical drops with an initial radius of 3.5 mm while drying. Surface stickiness of drops of fructose and maltodextrin solutions dried at 63degreesC and 95degreesC was determined. The effect of addition of maltodextrin on fructose solution-was studied with fructose/maltodextrin solid mass ratios of 4: 1, 1: 1, and 1:4. Pure fructose solutions remained completely sticky and failed cohesively even when their moisture approached zero. Shortly after the start of drying, the surface of the maltodextrin drops formed a skin, which rapidly grew in thickness. Subsequently the drop surface became completely nonsticky probably due to transformation of outer layers into a glassy material. Addition of malto,dextrin significantly altered the surface stickiness of drops of fructose solutions, demonstrating its use as an effective drying aid.
Description:
The change in textural attributes (hardness, chewiness and rate of softening) of three potato cultivars (Russet Burbank, Desiree and Sebago) was investigated. Uniform cylindrical samples (35-mm diameter and 3-mm thick) were prepared and exposed to different thermal processing regimes including; heating at 85°C, 95°C in water and steaming (100.2°C). The effect of salt on these textural attributes was also investigated using different salt concentrations (1.5%, 3% and 6% (w/w) NaCl). After thermal treatments the samples were subjected to texture profile analysis. The instrumental textural attributes were greatly affected by the cultivars and the thermal processing regimes. The change in textural attributes upon steaming was only marginally different compared to that at 95°C in water. Low concentrations of salt (1-3%) were found to accelerate the softening of the texture in these cultivars especially at lower temperatures. The textural attributes were modelled using a two-parameter reaction kinetics model. There was reasonable agreement by the model findings on the textural attributes prepared from all the thermal processing regimes and in presence and absence of (within average absolute error of 1.9-7%). Further, the model indicated that the order of reaction varied from 1.15-2.18 indicating that the changes in textural attributes in these thermal processing regimes followed higher reaction orders. [ABSTRACT FROM AUTHOR]
Description:
The viscoelastic property and scaling behavior of acid (glucono-delta-lactone)-induced soy protein isolate (SPI) gels were investigated at various ionic strengths (0-800 mM) and five protein concentrations ranging between 4% and 8% (w/w). The infinite storage modulus (G '(infinity)) and the gelation start time (t(g))which indicate the progress of gelation process exhibited strong ionic strength dependence. The storage modulus and critical strain were found to exhibit a power-law relationship with protein concentration. Rheological analysis and confocal laser scanning microscopy (CLSM) analysis were applied to estimate the fractal dimensions (D-f) of the gels and the values were found to vary between 2.319 and 2.729. The comparison of the rheological methods and the CLSM image analysis method showed that the Shih, Shih, Kim, Liu, and Aksay (1990) model was better suited in estimating the D-f value of acid-induced SPI gel system. (C) 2012 Elsevier Ltd. All rights reserved.
Description:
Polymeric aging in starch is an important equilibrating process leading to long-chain amylose recrystallization and anisotropic properties of material made from starch. Investigations into a number of plasticizers and hydrocolloids showed that their water retention/binding capability influence the starch polymer’s crystallinity. Addition of up to 8 wt % glycerol and 3 wt % xylitol acted as an antiplasticizer and apparently increased the total crystalline phase, which reduced the degree of elongation of amylose matrix by 15%. Maltodextrin and xanthan gum also reduced matrix elongation capability but X-ray diffraction (XRD) analysis showed samples with varying crystallinity, and the extent of crystallinity did not correlate with respective tensile properties. Additives such as maltodextrin, with similar molecular structure as amylose, were ineffective in increasing degree of elongation even at 15 wt % addition rate, because of formation of pockets of crystalline region, as observed by XRD analysis. Both xylitol and xanthan gum samples showed similar tensile strength and elongation properties, but the water retention capability of xylitol-filled starch samples was about 27% lower than xanthan gum samples, at their respective higher concentrations. A dynamic structural unit is proposed to satisfy the isotropic increase in tensile strength and degree of elongation in oriented starch matrix. VVC 2009Wiley Periodicals, Inc. J Appl Polym Sci 000: 000–000, 2009