The effect of low molecular weight surfactants and proteins on surface stickiness of sucrose during powder formation through spray drying
- Authors: Adhikari, Benu , Howes, Tony , Wood, B. J. , Bhandari, Bhesh
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 94, no. 2 (2009), p. 135 -143
- Full Text:
- Reviewed:
- Description: The effect of competitive surface migration of proteins and low molecular weight surfactants (LMS) on the powder recovery in spray drying of highly sticky sugar-rich food has been studied. Sucrose was chosen as a model sugar-rich food because it cannot be easily converted into a pure amorphous powder through spray drying. Sodium caseinate (Na-C) and hydrolyzed whey protein isolate (WPI) were used as model proteins. Polysorbate 80 (Tween-80) and sodium dodecyl sulfate (Na-DS) were used as model non-ionic and ionic LMS. A sucrose solution was spray dried without any additives to establish a base case. Following this, spray drying trials of sucrose-protein solutions were conducted. The sucrose: protein ratio was maintained at 99.5:0.5 and 99.0:1.0. Finally, 0.05% of Tween-80 and Na-DS, on a nominal feed basis, were individually added to the solutions and spray dried. The solid concentration of all of the feed solutions was set at 25% and the inlet and outlet temperatures were maintained at 170 °C and 70 °C, respectively. Powder recovery was determined using a standard procedure and taken as an indicator of the surface stickiness. Coverage of the particle surface by the proteins was determined through elemental surface analysis and a nitrogen balance. It was found that in the absence of LMS, the proteins covered up to 55% of the particle surface and increased the powder recovery to between 84% and 85%. Formation of a glassy protein-rich film acts to reduce the surface stickiness of sucrose droplets. However, when LMS was added to the sucrose-protein solutions, the recovery dropped to zero in the case of Tween-80. In the case of Na-DS the recoveries ranged to 39% and 68%. At these recoveries 83% and 59% of the protein, respectively, was displaced from the surface. This drastic effect of surfactant types on the powder recovery is explained using the Orogenic Displacement model. © 2009 Elsevier Ltd. All rights reserved.
Effect of addition of proteins on the production of amorphous sucrose powder through spray drying
- Authors: Adhikari, Benu , Howes, Tony , Bhandari, Bhesh , Langrish, Tim
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 94, no. 2 (2009), p. 144 -153
- Full Text:
- Reviewed:
- Description: Spray drying trials were carried out to produce amorphous sucrose powder. Firstly, pure sucrose solutions were prepared and spray dried at inlet and outlet temperatures of 160 °C and 70 °C, respectively. No amorphous powder was obtained and only 18% of the feed solids were recovered in a crystalline form, with the remaining solids lost as wall deposits. Secondly, sodium caseinate (Na-C) and hydrolyzed whey protein isolate (WPI) were added in sucrose:protein solid ratios of (99.5:0.5) and (99.0:1.0) and drying trials were conducted maintaining the initial drying conditions. In both these cases, greater than 80% of the feed solids were recovered in an amorphous form. The increase in protein concentration from 0.5% to 1% on dry solid basis did not further improve the recovery. The remarkable increase in recovery from a small addition of protein is attributed to preferential migration of protein molecules to the droplet-air interface, and the subsequent transformation of the thin, protein-rich film into a non-sticky glassy state upon drying. This film overcomes both the particle-to-particle and particle-to-wall stickiness. The measured bulk glass rubber transition temperature (Tg-r) values of the bulk mixtures at various moisture contents were very close to the corresponding mean glass transition temperature (Tg) of the pure sucrose indicating that surface layer Tg rather than the bulk Tg is responsible for this. Electron spectroscopy for chemical analysis (ESCA) studies revealed that the particle surface was covered by 50-58% (by mass) proteins. The calculated glass transition temperature of the surface layer (Tg,surface layer), based on the surface elemental compositions, showed that the Tg,surface layer has increased to the extent that it remained within the safe drying envelope of spray drying. © 2009 Elsevier Ltd. All rights reserved.
Guest Editorial: Special Thematic Issue on Drying of Proteins and Enzymes
- Authors: Adhikari, Benu , Devahastin, Sakamon , Mujumdar, Arun
- Date: 2013
- Type: Text , Journal article
- Relation: Drying Technology Vol. 31, no. 13-14 (2013), p. 1439-1440
- Full Text: false
- Reviewed:
- Description: The idea of publishing a special issue on proteins and enzymes was conceived during the 18th International Drying Symposium (IDS2012) held in the historical city of Xiamen, China (November 11-15, 2012). It appeared to us that a number of scientists and engineers were enthusiastically undertaking research in various aspects of drying of proteins and enzymes. Professors Arun Mujumdar and Sakamon Devhastin encouraged me to explore the possibility of bringing at least one special issue that would depict contemporary research undertakings in the broader theme involving proteins and enzymes. We were somewhat unsure in the beginning whether or not the required number of high quality mansucripts could be garnered for one issue in the time constraint we had in mind. Editorial
- Description: C3
Characterization of non-linear rheological behavior of SPI-FG dispersions using LAOS tests and FT rheology
- Authors: Bi, Chonghao , Li, Dong , Wang, Li-jun , Wang, Yong , Adhikari, Benu
- Date: 2013
- Type: Text , Journal article
- Relation: Carbohydrate Polymers Vol. 92, no. 2 (2013), p. 1151-1158
- Full Text: false
- Reviewed:
- Description: The effect of flaxseed gum (FG) on the rheological and nonlinear stress response behaviors of mixed soy protein isolate (SPI)-flaxseed gum (FG) dispersions were studied. Results showed that the viscosity of the SPI-FG mixed dispersions increased significantly with increase in the FG concentration. Both the shear stress and the apparent viscosity values as a function of shear rate were fitted well using Power law model as expected. The frequency dependence of G′, G′′ and tan δ of soy protein isolate decreased as the FG concentration increased. The large amplitude oscillatory shear (LAOS) test and Fourier transform (FT) rheology analysis showed that the addition of flaxseed gum strongly affected the structure of the SPI-FG mixed dispersion system as shown by deformation of the nonlinear stress response curve and significantly altered magnitude of higher harmonic curve. The addition of FG increased the instantaneous strain softening effect of the SPI-FG mixed dispersion system. © 2012 Elsevier Ltd.
- Description: 2003011034
Unexpected high pressure effects on the structural properties of condensed whey protein systems
- Authors: Dissanayake, Muditha , Kasapis, Stefan , Chaudhary, Vinita , Adhikari, Benu , Palmer, Martin , Meurer, Barbara
- Date: 2012
- Type: Text , Journal article
- Relation: Biopolymers Vol. 97, no. 12 (2012), p. 963-973
- Full Text: false
- Reviewed:
- Description: We show that application of high hydrostatic pressure (600 MPa for 15 min) on condensed whey protein (WP) systems (e.g., 80% w/w solids content) results in unexpected structure-function behavior when compared with conventional thermal treatment. Unraveling the relaxation properties in first-order thermodynamic transitions, the manifestation of glass transition phenomena and the preservation of native conformation in condensed preparations were recorded using small-deformation dynamic oscillation in shear, modulated differential scanning calorimetry, and infrared spectroscopy. Informed temperature application results in the formation of continuous networks at the denaturation temperature, which undergo vitrification at subzero temperatures. In contrast, high-pressure-treated WPs resist physicochemical denaturation, hence preserving the native conformation of secondary and tertiary structures. This was rationalized on the basis of a critical concentration threshold where transfer of water molecules to nonpolar residues in the protein interior is minimized because of low moisture content and restricted molecular mobility. The physical state and morphology of these high-solid preparations were further examined by the combined framework of reduced variables and Williams, Landel, and Ferry equation/free volume theory. Theoretical treatment of experimental observations unveils the dynamic range of the mechanical manifestation of the glass transition region in samples subjected to heat or pressure. In addition to preserving native conformation, WPs subjected to high pressure form glassy systems at parity with the structural functionality of the thermally treated counterparts. © 2012 Wiley Periodicals, Inc.
The effect of food-grade low-molecular-weight surfactants and sodium caseinate on spray drying of sugar-rich foods
- Authors: Jayasundera, Mithila , Adhikari, Benu , Adhikari, Raju , Aldred, Peter
- Date: 2010
- Type: Text , Journal article
- Relation: Food Biophysics Vol. 5, no. 2 (2010), p. 128-137
- Full Text: false
- Description: The effect of low-molecular-weight surfactants (LMS) and sodium caseinate (NaCas) on spray drying of sugar-rich foods has been studied. Sucrose and NaCas were selected as a model sugar-rich food and protein, respectively. Sodium stearoyl lactylate (SSL) and Polysorbate 80 (Tween 80) were chosen as model ionic and nonionic LMS. Sucrose-NaCas solutions with the solids ratio of 99.5:0.5 in the absence and presence (0.01% and 0.05%) of SSL and Tween 80 were prepared. The feed solutions had 25% solid concentration in all cases. The dynamic surface tension (DST) values of the solutions were measured for 100 s and the solutions were subsequently spray dried at inlet and outlet temperatures of 165 and 65 °C, respectively. The glass-rubber temperature (Tg-r), the surface elemental composition and amorphous-crystalline nature of the powders were also determined. At these concentrations and experimental time frame, it was found that the proteins preferentially migrated to the air-water interface reasonably swiftly. The addition of LMS resulted in partial or complete displacement of the proteins from the air-water interface. For spray-drying trials with the yield of 82.0%, it was found that 52.0% of the powder particle surface was covered with proteins. The powder recovery was greatly reduced by the LMS concentration and type. At 0.05% on dry solid basis, in the case of nonionic surfactant (Tween 80), the displacement of protein from the surface was such that no powder was recovered. The ionic surfactant (SSL) displaced 2.0% and 29.3% proteins from the droplet surface at concentrations of 0.01% and 0.05%, respectively, resulting in 75.5 ± 1.8% and 30.1 ± 1.4% powder yield. The Tg-r results revealed that the amount of protein required for successful spray drying of the sucrose-protein solution depends on the amount of proteins present in the droplet surface but not in the bulk. X-ray diffraction and scanning electron microscopy results confirmed that the powders of both sucrose-NaCas and sucrose-NaCas with 0.01% SSL were mostly amorphous, while those with sucrose-NaCas-Tween 80 (0.01%) and sucrose-NaCas-SSL (0.05%) were crystalline. © 2010 Springer Science+Business Media, LLC.
Surface modification of spray dried food and emulsion powders with surface-active proteins : A review
- Authors: Jayasundera, Mithila , Adhikari, Benu , Aldred, Peter , Ghandi, Amir
- Date: 2009
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 93, no. 3 (2009), p. 266-277
- Full Text:
- Reviewed:
- Description: Spray drying is a well-established and widely used method for transforming a wide range of liquid food products into powder form. Stickiness is the limitation in spray drying of different sugar and acid-rich food products. To minimize this problem process and material science based approaches are in place. However, these remedies have their own drawbacks. Surface modification of droplets/particles is a novel way to minimize stickiness. It is timely that the research efforts on surface modification of droplets/particles be reviewed. Therefore, this review highlights the recent research dealing with surface modification of emulsions and spray dried powders. The theoretical foundation, mechanisms and methods used to achieve surface modification of food and emulsion powders are highlighted. © 2009 Elsevier Ltd. All rights reserved.
The effects of proteins and low molecular weight surfactants on spray drying of model sugar-rich foods: Powder production and characterisation
- Authors: Jayasundera, Mithila , Adhikari, Benu , Adhikari, Raju , Aldred, Peter
- Date: 2011
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 104, no. 2 (2011), p. 259-271
- Full Text: false
- Reviewed:
- Description: The effects of proteins and low molecular weight surfactants (LMS) on spray drying and powder characteristics of model sugar-rich foods have been studied. Fructose and sucrose were selected as model sugar-rich foods and sodium caseinate (NaCas) was selected as a model protein. Sodium stearoyl lactylate (SSL) and Polysorbate 80 (Tween-80) were chosen as model ionic and non-ionic low molecular weight surfactants. The feed solutions for spray drying had 25% solid concentration in all. To achieve identical powder recoveries of the order of 80% much higher NaCas:fructose ratio (30:70) was required compared to NaCas:sucrose ratio (0.5:99.5) which corresponded to 7.89% and 0.13% of sodium caseinate (initial bulk concentration), respectively. There was no change in powder recovery when the SSL concentration was increased from 0.01% to 0.05% in fructose-NaCas-SSL solution and also addition of 0.01% Tween-80 into fructose-NaCas solution did not affect the powder recovery (76.7 ± 2.3%), however, it was slightly affected with the increase of Tween-80 to 0.05% (69.0 ± 1.9%). At NaCas concentration above critical micelle concentration of NaCas (3% w/w), the presence of up to 0.05% low molecular weight surfactants had either no effect or minimal effect on the surface coverage of the droplets/particles and also on the powder recovery depending on the nature of the low molecular weight surfactants. The surface protein coverage and the recovery of the powder in sucrose-protein systems were very sensitive in the presence of low molecular weight surfactants due to being below the critical micelle concentration of NaCas. SSL displaced 2.0% and 29.3% of proteins from the droplet surface of sucrose-NaCas-SSL, respectively, when its concentration was varied from 0.01% to 0.05% thereby reducing the powder recovery from 75.5% to 30%. The addition of 0.01% Tween-80 in sucrose-NaCas solution resulted in a 48.2 ± 1.5% reduction in powder recovery and at 0.05% concentration, it displaced a substantial amount of NaCas from the droplet surface and no powder was recovered. These phenomena are explained on the basis of surface-glass transition temperature, dynamic surface tension, nature of surfactants and glass transition temperature of sugars used. X-ray diffraction and scanning electron microscopy results showed that the powders of sucrose-NaCas, sucrose-NaCas with 0.01% SSL and all powders of fructose were amorphous. © 2010 Elsevier Ltd. All rights reserved.
Surface protein coverage and its implications on spray-drying of model sugar-rich foods: Solubility, powder production and characterisation
- Authors: Jayasundera, Mithila , Adhikari, Benu , Howes, Tony , Aldred, Peter
- Date: 2011
- Type: Text , Journal article
- Relation: Food Chemistry Vol. 128, no. 4 (2011), p. 1003-1016
- Full Text: false
- Reviewed:
- Description: We have investigated the amount of protein required to produce amorphous sugar powders through spray-drying. Pea protein isolate was used as a model plant protein and sodium caseinate was used as a model dairy protein. Powder recovery in a laboratory spray dryer was used as a measure of the ease of spray drying for a given formulation. More than 80% of amorphous sucrose and fructose was produced with the addition of sodium caseinate, while the pea protein isolate was able to produce only recoveries of less than 50% of amorphous sucrose. Sensitivity of low molecular weight surfactants has been demonstrated using both ionic (sodium stearoyl lactylate) and non-ionic (polysorbate-80) surfactants. Spray-dried powders were subjected to physico-chemical characterisation and dissolution experiments. The maximum solubility of all powders was obtained after 5 min of dissolution. The solubility of the sodium caseinate increased by 6-7% in the presence of fructose and low molecular weight surfactants. The solubility of the amorphous powders of sucrose-pea protein isolate was found to be lower than amorphous powders of sucrose-sodium caseinate and fructose-sodium caseinate. The addition of sucrose in water increased the solubility of the pea protein isolate from 16.84% to more than 83%. The non-ionic surfactant (Tween-80) has reduced the solubility of sucrose-pea protein isolate-Tween-80 powders significantly (p < 0.05) compared to those of sucrose-pea protein isolate-sodium stearoyl lactylate powders. The solubility of sucrose-sodium caseinate powders was comparable to that of pure sodium caseinate, indicating that addition of sucrose into 0.13% sodium caseinate does not have any significant effect on the solubility of this protein at this concentration. © 2011 Elsevier Ltd. All rights reserved.
Effect of gum Arabic on stability of oil-in-water emulsion stabilized by flaxseed and soybean protein
- Authors: Wang, Bo , Wang, Li , Li, Dong , Adhikari, Benu , Shi, John
- Date: 2011
- Type: Text , Journal article
- Relation: Carbohydrate Polymers Vol. 86, no. 1 (2011), p. 343-351
- Full Text: false
- Reviewed:
- Description: The effects of gum Arabic (GA) addition (0-4%, w/w) on stability of oil-in-water emulsion stabilized by flaxseed protein concentrate (FPC) and soybean protein concentrate (SPC) were studied. The result shows that emulsions stabilized by both proteins in the presence of the 2% gum Arabic (w/w) have better stability than its absence, by increasing the emulsion viscosity of the FPC stabilized emulsion and causing competitive adsorption between the GA and SPC layer to give a steric repulsion for the SPC stabilized emulsion, respectively. Then, the influences of ionic strength (0-200 mM NaCl) and temperature (25-95 °C for 20 min) on these emulsions in presence of GA were determined. The GA adsorbed at SPC-stabilized oil-water interface provided stability against NaCl concentration. In presence of GA, the SPC-stabilized emulsions also showed better stability at higher temperatures compared to the FPC-stabilized emulsions due to the denaturation of SPC and competitive adsorption between GA and SPC at higher temperatures. © 2011 Elsevier Ltd All rights reserved.
The effect of addition of flaxseed gum on the emulsion properties of soybean protein isolate (SPI)
- Authors: Wang, Yong , Li, Dong , Wang, Li Ming , Adhikari, Benu
- Date: 2011
- Type: Text , Journal article
- Relation: Journal of Food Engineering Vol. 104, no. 1 (2011), p. 56-62
- Full Text: false
- Reviewed:
- Description: The effect of addition of flaxseed gum on the emulsion properties of soybean protein isolate (SPI) were investigated in this study. Flaxseed gum with 0.05-0.5% (w/v) concentration was used together with 1% (w/v) SPI to emulsify 10% (v/v) soybean oil. The emulsion was analyzed for emulsion activity (turbidity), stability, particle size, surface charge, and rheological properties. The turbidity and absolute zeta-potential values decreased initially by the addition of flaxseed gum and subsequently increased with further increase in the gum concentration to reach their peak around 0.35% (w/v) gum. The particle size of the emulsion decreased and reached a minimum value at 0.1% (w/v) gum concentration. Any increase in gum concentration beyond this value resulted into increase in the particle size. This study would help to widen the application of SPI and flaxseed gum mixture, and also contribute to the understanding of protein-gum interaction in emulsion. © 2010 Elsevier Ltd. All rights reserved.