Optimal placement of synchronized voltage traveling wave sensors in a radial distribution network
- Authors: Tashakkori, Ali , Abu-Siada, Ahmed , Wolfs, Peter , Islam, Syed
- Date: 2021
- Type: Text , Journal article
- Relation: IEEE Access Vol. 9, no. (2021), p. 65380-65387
- Full Text:
- Reviewed:
- Description: A transmission line fault generates transient high frequency travelling waves (TWs) that propagate through the entire network. The fault location can be determined by recording the instants at which the incident waves arrive at various points in the network. In single end-based methods, the incident wave arrival time and its subsequent reflections from the fault point are used to identify the fault location. In heavily branched distribution networks, the magnitude of the traveling wave declines rapidly as it passes through multiple junctions that cause reflection and refraction to the signal. Therefore, detecting the first incident wave from a high impedance fault is a significant challenge in the electrical distribution networks, in particular, subsequent reflections from a temporarily fault may not be possible. Therefore, to identify a high impedance or temporary faults in a distribution network with many branches, loads, switching devices and distributed transformers, multiple observers are required to observe the entire network. A fully observable and locatable network requires at least one observer per branch or spur which is not a cost effective solution. This paper proposes a reasonable number of relatively low-cost voltage TW observers with GPS time-synchronization and radio communication to detect and timestamp the TW arrival at several points in the network. In this regard, a method to optimally place a given number of TW detectors to maximize the network observability and locatability is presented. Results show the robustness of the proposed method to detect high impedance and intermittent faults within distribution networks with a minimum number of observers. © 2013 IEEE.
Impact of load ramping on power transformer dissolved gas analysis
- Authors: Cui, Huize , Yang, Liuging , Li, Shengtao , Qu, Guanghao , Wang, Hao , Abu-Siada, Ahmed , Islam, Syed
- Date: 2019
- Type: Text , Journal article
- Relation: IEEE Access Vol. 7, no. (2019), p. 170343-170351
- Full Text:
- Reviewed:
- Description: Dissolved gas in oil analysis (DGA) is one of the most reliable condition monitoring techniques, which is currently used by the industry to detect incipient faults within the power transformers. While the technique is well matured since the development of various offline and online measurement techniques along with various interpretation methods, no much attention was given so far to the oil sampling time and its correlation with the transformer loading. A power transformer loading is subject to continuous daily and seasonal variations, which is expected to increase with the increased penetration level of renewable energy sources of intermittent characteristics, such as photovoltaic (PV) and wind energy into the current electricity grids. Generating unit transformers also undergoes similar loading variations to follow the demand, particularly in the new electricity market. As such, the insulation system within the power transformers is expected to exhibit operating temperature variations due to the continuous ramping up and down of the generation and load. If the oil is sampled for the DGA measurement during such ramping cycles, results will not be accurate, and a fault may be reported due to a gas evolution resulting from such temporarily loading variation. This paper is aimed at correlating the generation and load ramping with the DGA measurements through extensive experimental analyses. The results reveal a strong correlation between the sampling time and the generation/load ramping. The experimental results show the effect of load variations on the gas generation and demonstrate the vulnerabilities of misinterpretation of transformer faults resulting from temporary gas evolution. To achieve accurate DGA, transformer loading profile during oil sampling for the DGA measurement should be available. Based on the initial investigation in this paper, the more accurate DGA results can be achieved after a ramping down cycle of the load. This sampling time could be defined as an optimum oil sampling time for transformer DGA.
A new cascaded multilevel inverter topology with galvanic isolation
- Authors: Hasan, Mubashwar , Abu-Siada, Ahmed , Islam, Syed , Dahidah, Mohamed
- Date: 2018
- Type: Text , Journal article
- Relation: IEEE Transactions on Industry Applications Vol. 54, no. 4 (2018), p. 3463-3472
- Full Text:
- Reviewed:
- Description: IEEE This paper presents a new compact three-phase cascaded multilevel inverter (CMLI) topology with reduced device count and high frequency magnetic link. The proposed topology overcomes the predominant limitation of separate DC power supplies, which CMLI always require. The high frequency magnetic link also provides a galvanic isolation between the input and output sides of the inverter, which is essential for various grid-connected applications. The proposed topology utilizes an asymmetric inverter configuration that consists of cascaded H-bridge cells and a conventional three-phase two-level inverter. A toroidal core is employed for the high frequency magnetic link to ensure compact size and high-power density. Compared with counterpart CMLI topologies available in the literatures, the proposed inverter has the advantage of utilizing the least number of power electronic components without compromising the overall performance, particularly when a high number of output voltage levels is required. The feasibility of the proposed inverter is confirmed through extensive simulation and experimentally validated studies.
A novel concept for three-phase cascaded multilevel inverter topologies
- Authors: Hasan, Mubashwar , Abu-Siada, Ahmed , Islam, Syed , Muyeen, S.
- Date: 2018
- Type: Text , Journal article
- Relation: Energies Vol. 11, no. 2 (2018), p. 1-16
- Full Text:
- Reviewed:
- Description: One of the key challenges in multilevel inverters (MLIs) design is to reduce the number of components used in the implementation while maximising the number of output voltage levels. This paper proposes a new concept that facilitates a device count reduction technique of existing cascaded MLIs. Moreover, the proposed concept can be utilised to extend existing single phase cascaded MLI topologies to three-phase structure without tripling the number of semiconductor components and input dc-supplies as per the current practice. The new generalized concept involves two stages; namely, cascaded stage and phase generator stage. The phase generator stage is a combination of a conventional three-phase two level inverter and three bi-directional switches while the cascaded stage can employ any existing cascaded topology. A laboratory prototype model is built and extensive experimental analyses are conducted to validate the feasibility of the proposed cascaded MLI concept.