Description:
Water uptake behavior of three cultivars of lentils (Boomer, French-green and Nugget) was studied at three different hydration temperature regimes (room temperature, 50 °C and 85 °C). Boomer had the highest amount of water uptake capacity (74.60 g water/100 g of seeds) at room temperature (20 °C) which can be linked with its pore properties. French-green lentils imbibed the largest amount of water at elevated soaking temperatures (50 °C and 85 °C) and can be attributed to its higher seed surface area to volume ratio, high protein content and relatively thinner seed coat. Water uptake at elevated temperatures (50 °C and 85 °C) were predicted by a two parameter Mitscherlich model (R2 > 0.99,
The impact of various drying kinetics models on the prediction of sample temperature-time and moisture content-time profiles during moisture removal from stratum corneum
Description:
Polymeric aging in starch is an important equilibrating process leading to long-chain amylose recrystallization and anisotropic properties of material made from starch. Investigations into a number of plasticizers and hydrocolloids showed that their water retention/binding capability influence the starch polymer’s crystallinity. Addition of up to 8 wt % glycerol and 3 wt % xylitol acted as an antiplasticizer and apparently increased the total crystalline phase, which reduced the degree of elongation of amylose matrix by 15%. Maltodextrin and xanthan gum also reduced matrix elongation capability but X-ray diffraction (XRD) analysis showed samples with varying crystallinity, and the extent of crystallinity did not correlate with respective tensile properties. Additives such as maltodextrin, with similar molecular structure as amylose, were ineffective in increasing degree of elongation even at 15 wt % addition rate, because of formation of pockets of crystalline region, as observed by XRD analysis. Both xylitol and xanthan gum samples showed similar tensile strength and elongation properties, but the water retention capability of xylitol-filled starch samples was about 27% lower than xanthan gum samples, at their respective higher concentrations. A dynamic structural unit is proposed to satisfy the isotropic increase in tensile strength and degree of elongation in oriented starch matrix. VVC 2009Wiley Periodicals, Inc. J Appl Polym Sci 000: 000–000, 2009
Description:
The possibility of using milk permeate (MP) to lower the protein level of skim milk powder (SMP) in producing powders of 34% and lower protein is explored. Skim milk suspensions with various levels of MP were prepared by mixing SMP and MP powder (MPP) at the ratios of 1: 0, 7: 3, 3: 7, and 0: 1: from 34 to 5.3% protein. The suspensions were dried in a spray dryer with inlet and outlet temperatures of 180 and 80 degrees C, respectively. Increasing permeate concentration in the mixture showed a greater tendency to stickiness manifested by lowered the cyclone recovery of the powder as more powder stuck on the wall of the dryer. Increasing permeate concentration in the resultant powder did not significantly affect the bulk density but led to a reduction in the particle size and also made the powder slight green and yellowish in color. It also found to lower the glass transition temperature (T-g) of the skim milk powder (SMP) and induce crystallization of lactose at lower water activity (a(w) >= 0.328 for SMP: MPP of 3: 7 and 0: 1 compared to a(w) >= 0.0.432 for SMP: MPP of 1: 0 and 3: 7). Addition of MP in SMP lowered the Tg values of the resulting powders. The permeate fraction in spray-dried SMP/MPP mixtures found to lower the critical aw and moisture content, suggesting the SMP mixed with MPP is more likely to become sticky than SMP alone (at 34% protein) when stored at a similar water activity and moisture content.
Description:
Spray drying behavior of orange juice concentrate with various levels of maltodextrin (DE 6) was studied. Five combinations of orange juice concentrate and maltodextrin (25:75, 30:70, 35:65, 40:60, and 50:50) were spray dried at 160 and 65 degrees C inlet and outlet temperatures, respectively. The product recovered with 50% maltodextrin concentration was sticky and only 20% powder was recovered. The recovery of orange juice powder increased as the amount of maltodextrin in powders increased. The particle size and bulk density remained almost the same in all except in 50% maltodextrin powder which was slightly larger and more dense. The moisture content of spray dried powders was high and desiccated before measuring glass transition temperature. The anhydrous spray dried powders showed increased T-g values with increasing maltodextrin concentration, from 66 degrees C in 50% maltodextrin to 97 degrees C in 75% maltodextrin containing powders. The glass rubber transition ( Tg-r) values of all the products measured using novel Thermal Mechanical Compression Test (TMCT) were higher than T-g values measured by DSC; the difference in values increased with increase in maltodextrin concentration.
Description:
The estimation of a concentration-dependent diffusion coefficient in a drying process is known as an inverse coefficient problem. The solution is sought wherein the space-average concentration is known as function of time (mass loss monitoring). The problem is stated as the minimization of a functional and gradient-based algorithms are used to solve it. Many numerical and experimental examples that demonstrate the effectiveness of the proposed approach are presented. Thin slab drying was carried out in an isothermal drying chamber built in our laboratory. The diffusion coefficients of fructose obtained with the present method are compared with existing literature results. (c) 2006 Elsevier Ltd. All rights reserved.